2 24 WS-C3750G-24T 12.2(35)SE5 C3750-IPBASEK9-M. Download Latest IOS Image from Cisco Website. Download the latest IOS image for your cisco website Go to cisco.com - IOS Software - Select your Siwtch (for example: Cisco Catalyst Switch 3750G-24T) - Click on 'Download IP BASE' - Select the latest version that you want to download (for. Cisco IOS Software, C3750 Software (C3750-ADVIPSERVICESK9-M), Version 12.2(25)SE. Cisco WS-C3750-48P (PowerPC405) processor (revision N0) with 118784K/12280K byte.
Anytime Cisco releases a new IOS image for its network switch (or router), it is recommended that you upgrade it.
This article explains 7 easy steps to upgrade IOS image on a cisco switch or router.
Since you'll be upgrading the IOS image, make sure you have physical access to the switch and you are in front of it. Use a console cable to connect to the switch.
Please note that the steps given below will be similar to both switches and routers. However this examples shows how to upgrade ios image on a cisco catalyst switch.
1. Verify Current IOS Version
After you login, go to enable mode, by entering the enable password. This example uses two cisco catalyst 3750 switches configured in stack mode as shown below. So, while upgrading you should upgrade the image on both the flash cards.
If you have only one cisco catalyst switch (non stack mode), follow all the steps mentioned in this document, but you'll be doing it only on one flash card.
First, verify the content of the flash cards, using 'dir flash1:' command.
As you see above, both the flash cards contains the current IOS image file, which is version '122.35.SE5'
Verify what version of IOS image your switch is currently running. Most likely this will be same as the current IOS image file that you see in your flash card. As you see below, it is using '12.3(35)SE5'
2. Download Latest IOS Image from Cisco Website
Download the latest IOS image for your cisco website
Go to cisco.com -> IOS Software -> Select your Siwtch (for example: Cisco Catalyst Switch 3750G-24T) -> Click on 'Download IP BASE' -> Select the latest version that you want to download (for example: 12-2.55.SE1).
While you are on this download page, copy/paste the MD5 given to your system. After we download the IOS image and move it to the switch, we'll verify the MD5 checksum before installing the image.
3. Delete Old IOS Software Image from Flash
Since we'll be downloading the new ISO image and moving it to the flash card, we need some space. So, delete the current old image from the flash card.
In the above delete command, /f stands for force, and /r stands for recurssive.
On a side note, you should be using some software to monitor your switch status. If you are not doing it install Nagios, and monitor your switches.
4. Copy the IOS image to Cisco Switch
To transfer the IOS image from your laptop to Cisco Switch, you should run a TFTPserver on your laptop (or on the system where you've downloaded the IOS image).
If you are running a TFTPserver on your laptop, and connected to the switch using a console cable, assign a ip-address to your laptop, and put your laptop on the same network as the switch.
Copy the ISO image to the flash as shown below using the 'copy command'. This will ask you to enter the address of the remote host (which is your laptop in this case), and the source filename that needs to be transferred (which is the ISO image you downloaded from cisco website).
Once you've copied it, make sure the file is there on the flash card.
Just to make sure nothing went wrong during the copy, do a MD5 check-sum on this, and compare with the MD5 that you noted down from cisco website while downloading the IOS image. To create MD5 checksum of a file in Cisco catalyst switch, use the 'verify' command as shown below.
If you are running two switches in stack configuration, do the same on the second flash card.
5. Modify Switch Boot path-list
Now it is time to tell switch cisco to use the new ISO image to boot from. Before changing the boot information, verify the current configuration, and change it using the 'boot system' command as shown below.
6. Save Config and Restart the Switch
Verify the current boot information, save the current configuration, and reboot the cisco switch as shown below.
7. Final Verification after IOS Upgrade
Finally verify the current IOS version of the switch, after the upgrade, it should display the new version as shown below.
Make sure to verify your interface and vlan status, to make sure everything is running properly without any issues.
If you enjoyed this article, you might also like..
Next post: 20 Tips to Simplify Your Digital and Online Life
Previous post: 7 Linux chkconfig Command Examples – Add, Remove, View, Change Services
Cisco 3750 Ios Download
3750-x switch is having an advanced feature for rommon recovery. for other switches we used to do xmodem recovery. for 3750-x switch we do not have to waste time like that.
follow the procedure, we can set the ipaddress even in the rommon prompt and transfer the image
Step 1 Connect your PC to the switch Ethernet management port.
Step 2 Unplug the switch power cord.
Step 3 Press the Mode button, and at the same time, reconnect the power cord to the switch.
You can release the Mode button a second or two after the LED above port 1 goes off. Several lines of information about the software appear with instructions:
The system has been interrupted prior to initializing the flash file system. The following
commands will initialize the flash file system, and finish loading the operating system
software#
flash_init
boot
Cisco Ws-c3750-24p Ios
Step 4 Initialize the flash file system:
switch: flash_init
3. Delete Old IOS Software Image from Flash
Since we'll be downloading the new ISO image and moving it to the flash card, we need some space. So, delete the current old image from the flash card.
In the above delete command, /f stands for force, and /r stands for recurssive.
On a side note, you should be using some software to monitor your switch status. If you are not doing it install Nagios, and monitor your switches.
4. Copy the IOS image to Cisco Switch
To transfer the IOS image from your laptop to Cisco Switch, you should run a TFTPserver on your laptop (or on the system where you've downloaded the IOS image).
If you are running a TFTPserver on your laptop, and connected to the switch using a console cable, assign a ip-address to your laptop, and put your laptop on the same network as the switch.
Copy the ISO image to the flash as shown below using the 'copy command'. This will ask you to enter the address of the remote host (which is your laptop in this case), and the source filename that needs to be transferred (which is the ISO image you downloaded from cisco website).
Once you've copied it, make sure the file is there on the flash card.
Just to make sure nothing went wrong during the copy, do a MD5 check-sum on this, and compare with the MD5 that you noted down from cisco website while downloading the IOS image. To create MD5 checksum of a file in Cisco catalyst switch, use the 'verify' command as shown below.
If you are running two switches in stack configuration, do the same on the second flash card.
5. Modify Switch Boot path-list
Now it is time to tell switch cisco to use the new ISO image to boot from. Before changing the boot information, verify the current configuration, and change it using the 'boot system' command as shown below.
6. Save Config and Restart the Switch
Verify the current boot information, save the current configuration, and reboot the cisco switch as shown below.
7. Final Verification after IOS Upgrade
Finally verify the current IOS version of the switch, after the upgrade, it should display the new version as shown below.
Make sure to verify your interface and vlan status, to make sure everything is running properly without any issues.
If you enjoyed this article, you might also like..
Next post: 20 Tips to Simplify Your Digital and Online Life
Previous post: 7 Linux chkconfig Command Examples – Add, Remove, View, Change Services
Cisco 3750 Ios Download
3750-x switch is having an advanced feature for rommon recovery. for other switches we used to do xmodem recovery. for 3750-x switch we do not have to waste time like that.
follow the procedure, we can set the ipaddress even in the rommon prompt and transfer the image
Step 1 Connect your PC to the switch Ethernet management port.
Step 2 Unplug the switch power cord.
Step 3 Press the Mode button, and at the same time, reconnect the power cord to the switch.
You can release the Mode button a second or two after the LED above port 1 goes off. Several lines of information about the software appear with instructions:
The system has been interrupted prior to initializing the flash file system. The following
commands will initialize the flash file system, and finish loading the operating system
software#
flash_init
boot
Cisco Ws-c3750-24p Ios
Step 4 Initialize the flash file system:
switch: flash_init
Step 5 Connect the switch to a TFTP server through the Ethernet management port.
Step 6 Start the file transfer by using TFTP.
a. Specify the IP address of the TFTP server:
switch: set ip_addr ip_address/mask
b. Specify the default router:
switch: set default_router ip_address
Cisco Ws-c3750-48p Ios Download
Step 7 Copy the software image from the TFTP server to the switch:
Cisco 3750 Ios Upgrade
switch: copy tftp://ip_address/filesystem:/source-file-url flash:image_filename.bin
Step 8 Boot up the newly downloaded Cisco IOS image.
switch: boot flash:image_filename.bin
http://www.cisco.com/en/US/docs/switches/lan/catalyst3750x_3560x/software/release/12.2_55_se/configuration/guide/swtrbl.html#wp1099467